We investigated graphene-based transparent electrodes for InGaN/GaN light emitting diodes(LED). Nano-dotted layer of Ag and Ni were inserted between p-GaN and graphene to achieve low contact resistance and high transmittance. Heat treated Ag layer/graphene had low contact resistance of 0.7~1.2Ω/cm2, and we could achieve better luminance for GaN-based LED. However, for patterned Ni layer/graphene
어떻게?
① Metal을 이용
☞ Contact Resistance ↓, but Transmittance ↓
② Graphene을 이용
☞ Transmittance ↑, but Contact Resistance ↑
③ Metal/Graphene layer를 이용
☞ Transmittance ↑, Contact Resistance ↓
④ Patterned metal + Graphene을 이용 !! ↕:Good
☞ Transmittance ↑↑, Contact Resistance ↓↓ ↕: Bad
1. 서론
지난 30년간 리소그래피 기술은 반도체 소자의 발전과 더불어 광 투사 리소그래피(Optical Projection Lithography) 기술을 중심으로 지속적인 발전을 거듭하였다. 그리하여 지금 193 nm의 광 투사 리소그래피를 이용하여 100 nm 이하의 선 폭을 형성할 수 있는 수준에 이르렀다. 그러나 반도체 기술은 앞으
때문에 비용이 많이 드는 편이다. 광학적 성질이 우수하기 때문에 내시경같은 광학기계의 재료로 쓰이며 최근의 통신 선로로 각광받고 있는 광섬유의 주 원료이기도 하다. 뛰어난 내열성 때문에 우주왕복선의 아랫날개, 수직 꼬리날개 같은 부분의 방열 타일(heat-resistant tile)재료로 쓰이기도 한다.
Semiconductor-Grade Silicon
Steps to Obtaining Semiconductor Grade Silicon (SGS)
1 Produce metallurgical grade silicon (MGS) by heating silica with carbon
SiC (s) + SiO2 (s) Si (l) + SiO(g) + CO (g)
2 Purify MG silicon through a chemical reaction to produce a silicon-bearing gas of trichlorosilane (SiHCl3)
Si (s) + 3HCl (g) SiHCl3 (g) + H2 (g) + heat
3 SiHCl3 and hyd
, 금박에서 볼 수 있다. 전혀 가열하지 않고 단순히 기계적 압력만으로써 접합한다.
③ pressure welding (압렵용접)
- 용접에 열이 필요하지만 부분적으로 용융되지 않는 것으로, 면경계를 넘어 재결정이 일어난다. 금박은 열을 가하지 않고도 용접된다. resistance welding 또는 spon welding이라고도 한다.
resistance
Wider operating temperature range (0 C–45 C) and pH range (from 1 to 11)
Higher stability to biological attack
Chlorine and fouling susceptibility
The key point of the RO membrane
Flux
Salt rejection
※ Problems
- fouling
- permeability
- energy consumption
Fouling
Main cause
- algae, microorganism, cationic foulants.
- We should replace the reve
Introduction
An analytical technique
Separating ions or molecules that are dissolved in a solvent.
Mobile phase : liquid
Stationary phase : liquid or solid
The stationary phase for adsorption chromatography
Silica(SiO2 · xH2O)
Alumina(Al2O3 · xH2O)
Solvents for adsorption chromatography
Solvent competes with solute for adsorption sites on the stationary phase
The more strongly